Let's talk!

7 Easy Ways to Fix Linksys RE6500 Extender Orange Light Issue

  • click to rate

    When you turn on your Linksys RE6500 extender, its power LED will blink amber for a few seconds and then become blue. But what if the Linksys extender power LED remains orange/ amber for too long? Alas! To fix Linksys RE6500 extender amber or orange light issue, walk through the easy-to-execute troubleshooting fixes given in the post. Let’s get the ball rolling!

    Resolved: Linksys Extender Orange Light Issue

    1. Check the Connection

    When your Linksys RE6500 extender can’t connect to your router or gateway via a wired or WiFi connection, possibilities are that you may experience the orange color LED issue. To fix it, make sure that you have made a proper connection between your router and Linksys extender.

    2. Cross-Check the Ethernet Cables

    Are you using a damaged Ethernet cable? If you nod in yes, then we suggest you replace the damaged Ethernet cable with a new one. This will help you in fixing the orange color LED issue on your Linksys RE6500 extender.

    3. Check the Power

    Your Linksys extender must receive continuous power supply from the working and damaged-free wall socket. To prevent this, plug your Linksys extender into a fluctuation-free and non-damaged wall outlet.

    4. Power Cycle your Linksys Extender

    Power cycling your Linksys RE6500 extender can also help you fix orange/ amber LED issue. To power cycle your Linksys extender, do the following:

    • Disconnect all the connected devices that are connected to your Linksys device.

    • Unplug your Linksys WiFi extender.

    • Wait for a few minutes.

    • Plug in your Linksys RE6500 extender back again.

    • Connect your devices again to the extender.

    As soon as you are done with power cycling, try to do the Linksys RE6500 setup process and check if the device still shows an amber color LED.

    5. Update your Linksys Extender Firmware

    On the off chance if none of above-mentioned troubleshooting ways solves the Linksys extender amber LED issue for you, then the reason may be the outdated firmware on your Linksys extender. Check for the firmware update for your RE6500. And if the new/ latest firmware is available, update it right away via http // extender.linksys.com.

    6. Reset your Linksys RE6500 WiFi Extender

    Is the orange color LED still there on your Linksys extender? If so, try resetting your Linksys extender. The factory reset process will give your Linksys extender a new start. To get the job done, do the following:

    • Power on your Linksys WiFi extender.

    • Disconnect RE6500 from your router.

    • Locate the Linksys extender’s reset hole, and once found, push it with a pin or paper clip.

    • Hold the reset hole for a couple of seconds and release it.

    • Wait for some time for your extender to reboot.

    Done! Your Linksys extender has been reset successfully. You can configure it again using the default settings and Linksys extender login credentials.

    7. Set up your Linksys Extender

    This can be one of the main reasons behind the issue. To fix it, set up your Linksys extender properly after the reset process. To do so:

    • Power on your Linksys extender.

    • Connect RE6500 to your main router.

    • Turn on a PC or laptop, open a web browser on it, and enter extender.linksys.com in the address bar.

    • Press Enter.

    • Linksys RE6500 Setup page displays.

    • Click on Start Setup.

    • Follow the instructions and soon your device will be configured successfully.

    After completing the Linksys extender setup process, the RE6500 power LED will blink for a short while and then become lit.

    Verdict

    We hope that Linksys RE6500 extender orange/ amber LED issue has been fixed. In the event that you still experience the same issue, contact our experts now through the comments section and get it fixed within a matter of minutes.